-
product
FPGA PXI Card with 40 Channel ECL Buffer Module
GX3640
The GX3640 is comprised of the GX3500 FPGA card and the GX3540, 40 channel ECL expansion card. It is a 3U PXI instrument card that can be used for general data acquisition, process control, Automatic Test Equipment (ATE), and functional test applications. The GX3640 consists of 20 differential ECL drivers and 20 differential ECL receivers. Each channel can be accessed via software commands for use in static I/O applications.
-
product
SparkFun SD/MMC Card Breakout
With SD and MMC memory prices dropping, the time is right for mass storage and datalogging. This breakout board will allow you to breakout the SD/MMC socket to a standard .1" 10-pin header. Perfect for breadboarding and the likes. Board comes fully assembled and tested as shown.
-
product
Express Card
EXC-1553ExCard/Px
Each channel of the EXC-1553ExCard/Px operates simultaneously as a Bus Controller and/or multiple (up to 32) Remote Terminals, or as a Triggerable Bus Monitor. The card supports error injection and detection. The card’s small size and compatibility with notebook computers make it the perfect solution for performing system simulation of the MIL-STD-1553 bus, in the lab and in the field.
-
product
48-CH DIO & Timer/Counter Cards
cPCI-7248/7249R
- PICMG 2.0 Rev 2.1- 48-CH digital TTL/DTL input/output- Emulates 4/2/1 industry standard 8255 PPI (mode 0)- Direct interface with OPTO-22 compatible I/O modules Output port status read back- On board 8254 timer/counter chip
-
product
Capacitance Simulation Card
SET-1220
The SET-1220 device is a designed capacitive fuel sensor emulation for NI-SLSC. This card provides eight isolated channels that can emulate capacitance values between 10pF and 800pF. It was designed to emulate capacitive sensors that are typically connected between an excitation voltage on one end and a virtual ground on the other end.
-
product
FPGA Mezzanine Card
FMC424
Electrically compliant with the VITA 57.1 standard, the FMC424 is compatible with Abaco Systems' FPGA carrier cards offering high pin count connectors. It also allows for the option to stack an additional FMC over it.
-
product
Digital Signal Processor Card
CHAMP-FX2
Curtiss-Wright Defense Solutions
Utilizing a 6U VPX-REDI form factor, the CHAMP-FX2 FPGA-based computing platform harnesses the tremendous computing power of two Xilinx Virtex-5 FPGAs, combined with the high-performance floating-point capabilities of the NXP (formerly Freescale) MPC8641D dual-core Power Architecture processor and the performance and flexibility of a Serial RapidIO switching fabric to flexible computational performance.
-
product
SIMRC Card Carrier
1050-001
The SIM Relay Carrier 1050 simplifies the custom integration of small format embedded switching cards. No additional PCB design is necessary. Due to the Eurocard format the carrier can be fitted into a standard case or can be mounted in a 19" rack with side rails. Plug in standard SIM Relay Cards and control your switch application with the provided Soft Front Panel without any additional programming.
-
product
Audio Card I/O Modules
PIM481-J/DSUB
The PIM481-J PMC I/O Module, with four 3.5mm stereo connectors and the PIM481-DSUB PMC I/O Module, with D-sub for rear I/O can be mounted on a rear transition module (RTM).
-
product
PCI Matrix Cards
PCI Matrix cards are available in the following:*Reed relay based matrices available in 22x4, 22x8, 44x4 or dual 20x4 formats with 1-pole, 2-pole or 1-pole screened relays*2 Amp electro-mechanical relay based 1-pole matrices available in 32x2, 32x4, 16x4, 16x8 or 8x8 formats.*Select modules are supplied with our eBIRST Switching System Test Tools, these tools provide a quick and simple way of finding relay failures within LXI, PCI and PXI switch systems.
-
product
6U Horizontal Card
733
VECTOR Electronics and Technology, Inc.
Chassis for horizontal card installation
-
product
32-Bit CardBus Card
GPIB-PCMCIA-XL
The GPIB-PCMCIA-XL is the ideal solution for connecting GPIB instruments to mobile computers.
-
product
Circuit Card Assembly
Teledyne Advanced Electronic Solutions assembles and tests a variety of complex circuit card assemblies (CCAs) using leading edge, advanced technology assembly automation. We specialize in low-volume, high-mix assembly of highly complex CCAs.- RF, analog, high-speed and digital circuits on rigid-flex and Cu core substrates- Typical lot sizes from 3 to 300 pieces- 4 high speed, flexible SMT lines- Production processes for components from 0201 chips to large grid-array components and connectors- 100% solder paste, automated optical, and x-ray inspection- Forced air convection reflow with inert atmosphere option- Special processes for RF assemblies (filters, shields, etc)- BGA underfill, conformal coating, etc.- Selective and wave solder pin-thru-hole processes- CCA and component bonding processes
-
product
PXIe Avionics Interface Cards
The OmniBus II PXIe is the next-generation of Astronics' popular OmniBus product with faster I/O and processing capabilities. With the newest advanced set of MIL-STD-1553 and ARINC 429 modules, users can verify wave form compatibilities, test functions of bus shorts and opens, and—when combined with our CoPilot® software—perform lab, production and flight test verification and simulation right out of the box. Readily available as Commercial Off-The-Shelf (COTS) products, the PCIe interface is perfect for challenging simulation, test, interface, and data recording applications.
-
product
TTENetwork Interface Cards
The TTENetwork Interface Cards are pluggable mezzanine cards for network communication combining regular Ethernet with the safety-critical time-triggered technology from TTTech. They enable real-time Gbit/s Ethernet communication between a computer and TTESwitches for redundant channels in a safety-critical way.
-
product
128-Channel Scanner/Multiplexer PXI Card
GX6264
The GX6264 is a 6U PXI scanner / multiplexer that plugs directly into an PXI or CompactPCI backplane. The GX6264 provides either differential or single-ended scanning capability, configurable via software commands or DIP switches.
-
product
Serial Communications Card
104-ICOM-2S
The Model 104-ICOM-2S Serial Communications Card can be installed in a PC/104 stack and provide effective communication on long lines in noisy environments. Data lines are opto-isolated from the computer and from each other to assure communication even when large common mode voltages and noise are imposed.
-
product
GPIB Controller Card
GPIB-PC104-XL
The GPIB-PC104-XL is a PC/104 GPIB controller card that converts any PC/104 based embedded system into a GPIB controller.
-
product
Carrier Card
VIPC627-ET
VIPC627-ET is a 6U VME carrier card with four IP slots and extended temperature range. Two 50-pin, 0.1 inch flat ribbon cable connectors mounted in the front panel provide access to all IP I/O lines. Also, all I/O lines of 'IP D' are routed to VME P2 and 14 user selectable I/O lines of 'IP C' can be routed to VME P2 via a jumper field.
-
product
Radio Module with PCIe Card
SX-PCEAC2
The SX-PCEAC2 is powered by Qualcomm Atheros radio chip, the QCA6174-5, which features 2x2 wave 2 MU-MIMO technology. It is a dual-band 802.11 a/b/g/n/ac module with Bluetooth support which is designed for devices that require wireless connectivity in a small form factor combined with high performance with throughputs reaching up to 867Mbps.
-
product
FPGA Mezzanine Card
FMC160
The FMC160 provides one 12-bit A/D channel at 3.6Gsps and one 14-bit D/A channel at 5.7Gsps (2.85Gsps direct RF synthesis) clocked by either an internal clock source (optionally locked to an external reference) or an externally supplied sample clock. In addition, a trigger input for customized sampling control is available to users. It is mechanically and electrically compliant with the FMC standard (ANSI/VITA 57.1).
-
product
Digital Input/Output Cards
PCI-DIO Series 24 and 48
The PCI-DIO-48/48S, PCI-DIO-48JP/JPS, PCI-DIO-48JPL/JPLS, PCI-DIO-48H/HS and PCI-DIO-24S are 24- and 48-bit parallel digital input/output cards designed for use in PCI-Bus computers. The card is 6.9 inches (175 mm) long and may be installed in any 5-volt PCI slot in IBM and compatible computers.
-
product
PCI Card
EXC-4000PCI/xx
Each channel using the M4K1553PxS (RT validated) module operates either as a Bus Controller, Remote Terminal, or Bus Monitor.NOTE: the M4K1553PxS module is NOT compatible to the M4K1553MCH module.The EXC-4000PCI/xx is supplied with C drivers (including source code), Merlin+ Windows software and may be used with Exalt, Excalibur’s Analysis and Laboratory Tools, a Windows monitoring application. Mating connector provided for I/O connection.
-
product
FPGA Mezzanine Card
FMC172
The Abaco FMC172 wideband low latency FMC module is based on the latest high performance ADC device from Texas Instruments and DAC devices from Teledyne-E2V. It is the fastest ADC Abaco offers with LVDS interfaces, delivering up to 6.4 GSPS ADC on a single channel (or two channels @ 3.2 GSPS) and a single channel DAC at up to 6.0 GSPS, making it among the fastest low-latency devices available on the market. The combination of the FMC172's >6.0 GHz bandwidth, its high sample rate and low latency is ideal for advanced Digital RF Memory (DRFM) systems.
-
-
product
GPGPU Cards
Curtiss-Wright Defense Solutions
For applications requiring massive parallel compute capability, such as deep learning frameworks for AI applications, our highly engineered GPGPU co-processing engines provide a field-proven hardware foundation. Curtiss-Wright GPGPU co-processing engines leverage the latest NVIDIA Tensor Cores (for machine learning) technology and are a critical component of the high-performance embedded computing (HPEC) ecosystem that delivers data center capability at the tactical edge.
-
product
Data Acquisition Card
TPCE
The Elsys TPCE data acquisition (DAQ) cards are high-precision and high-resolution digitizers with sophisticated features such as advanced trigger mode, continuous data acquisition mode, differential inputs, digital input lines (Markers) and ICP coupling for powering piezo sensors.
-
product
XMC Display Control Card
XM26001
LinkedHope Intelligent Technologies Co.,Ltd.
XM26001 is a graphics, image processing and computing single-board computer independently developed by Linghao Intelligent®. It uses the AMD G series APU GX-210HA by default, integrating the CPU, GPU, south bridge and north bridge on one silicon chip.
-
product
S_A_Relay Card
The Stand Alone Relay accepts a regular PC style power connector that powers two relays. Upon power failure, the relays disengage the two ethernet lines so as to not interrupt communication on the ethernet lines. A CPLD allows for pass through and bypass of Ethernet signals. 10/100 Ethernet compatible. The CPLD is controlled via user input.
-
product
ARINC818 Cards
> ARINC818 is a specification which has become an Industry standard for the transmission of uncompressed digital video. This commercial standard uses Fibre Channel as a point-to-point communication link for low latency with the ARINC818 defining the packetized protocol for transmission of the digital video information. It is highly flexible and can be used for a variety of onboard display systems in both commercial and military applications. AIM’s ARINC818 cards use our field proven Common Core hardware design giving the best performance, best feature set and highest functional integration on the market. The use of SoC (System on Chip) based core designs with one dual core RISC processor per port, massive DDR3 memory and IRIG-B time encoder/decoder functions are standard. The ARINC818 modules are available in PCIe formats.The new ultra high performance intelligent 4-lane PCIe 2.0 interface modules offer 2 ports with full function test, simulation, monitoring and analyzer functions for ARINC818 interfaces. The dual core processor provides onboard processing and data transfer capabilities for the most demanding applications including ARINC818 support done on board level. Large and high data throughput DDR3 RAM is accessible for the onboard processor as is a high performance FPGA implementing the customized ARINC818 Interfaces enabling the board to analyze incoming data in real time. Each module provides 2 ARINC818 compliant ports. SFP cages make it suitable for different media types as optical or electrical network technologies. Each module is delivered with a Board Support Package (BSP) containing the onboard driver software, a full Application Programming Interface (API) and detailed getting started and programming guides. Powerful PBA.pro databus test and analysis software is optionally available for all our ARINC818 cards.
